Pellet Richi

Pellet Richi

Pellet machine manufacturer
https://www.pellet-richi.com/

How to make the wood pellet mills mold and mildewm

Pellet Richi
Pellet Richi 3/9/2023 8:18:16 AM

How to make the wood pellet mills  mold and mildew  much more " long life".

In recent years, the  environmental management  plans of various countries  have actually  ended up being more and more strict. As a  rep of  brand-new energy, biomass pellets  have actually  progressively  come to be  preferred,  and also biomass pellets in  lots of  locations  have actually  also been in short supply. Along with biomass pellets, there are  likewise sawdust pellet  devices that produce biomass pellets. From the  initial  level die wood pellet machine to the current ring die wood pellet mills, they are  continuously being  upgraded.

1.  Just how to  extend the service life of wood pellet mills  mold and mildew?

The mold is a  susceptible  component in the sawdust wood pellet mills,  as well as it  requires to be  changed  constantly. The  pricey  mold and mildew is also a major  expense in the production process of the sawdust pellet.  Exactly how to  boost the  life span of biomass  timber pellet mills  mold and mildew?

( 1)  Load the  mold and mildew with oil

After the daily  handling and  manufacturing  mores than,  utilize oil to grind the  mold and mildew  opening for a period of time to  make sure that all oil is left in the  mold and mildew hole, which is of  wonderful  advantage to the next day's  job and is also  for the  lasting  use the  mold and mildew.

Related post: wood pellet mill cost 

( 2)  Frequently  tidy up the oil

The editor here reminds  every person that if the wood pellet mills are not used for  greater than a month, it is best to take out the oil in the mold. Because the oil will  progressively  set  throughout the long-term storage process, which  will certainly make it  hard to  eliminate the  following time it is  utilized, which  will certainly affect the subsequent use of the  timber pellet mills.

( 3) It is not  needed to  clean up the  mold and mildew for a  long period of time

If the wood pellet mills are not  utilized for a  long period of time, it is  suggested to  eliminate the mold, clean it  and after that  keep it. It  primarily  cleanses the pellets inside the  mold and mildew  and also the sawdust  connected to the surface of the mold. In this way, on the one hand, it  avoids the pellets from being  solidified  as well as  challenging to  eliminate due to  lasting storage,  as well as on the other hand, it  lowers the  rust of sawdust to the mold.

( 4) The mold  must be  kept in a  completely dry and ventilated  location

Most of the molds of the wood pellet mills are  made from alloy steel. If they are in a  moist  area for a long time, the  surface area of the  mold and mildew may be  harmed  as a result of  rust  and also its service life  will certainly be  minimized.

( 5) The  managing process  ought to be  thoroughly

The mold of the wood pellet mills is a high-precision  device. If the  framework of the inner  wall surface of the die  opening is  harmed  throughout the  managing process, it may  create the failure of the  timber pellet  maker  and also  reduce the  life span of the wood pellet  maker.

Related post: https://www.pellet-richi.com/wood-pellet-machine/wood-pellet-mill.html 

The above are  5  suggestions to  extend the  life span of the  timber pellet  device.  Adhere to these  5  techniques to maintain the mold, and I  think your mold  will certainly last  much longer.

2. How to  address the blockage of the  mold and mildew of the  timber pellet mill machine?

With the popularization of the  principle of  environmental management  as well as saving, wood pellet machine is  identified  as well as  approved by  an increasing number of  clients,  and also  inhabits an  progressively important  placement in our  manufacturing.  Nevertheless, in the process of  utilizing the  complete  timber pellet mill  device, there are  constantly  numerous  troubles. Today, Richi Machinery  will certainly  present to you  just how to solve the  clog of the mold of the  timber pellet mills  devices.

If you  would like to know the  option to the  issue, you must  initially  discover the cause of the  trouble,  as well as to  fix the problem of blockage of the wood pellet  device, you  have to  discover the cause of the  clog of the wood pelleting machine.

The main  factors for the  clog of the sawdust  timber pellet mills  mold and mildew are as follows:

1. The feed of the  timber pellet mills is  also fast  as well as the  result is  also  slow-moving.

Solution: Replace the die of the wood pelletizer  equipment, or reduce the feed rate.

Related post: wood pellet production line 

2. The raw  products  have impurities, such as nails,  blocks, etc.

 Remedy:  Switch off the  timber pellet mills equipment,  after that  open up the  mold and mildew cover, then pour out the extruded  basic material,  clean the impurities in the raw  product, and  placed the raw material back. Note: When replacing the  mold and mildew cover, tighten the nut.

3.  Improper control of  basic material  wetness, or  too much  bit size,  and so on, will  additionally  create  obstruction of the  timber pellet mills mold,  and also  hand-operated cleaning is very difficult.

 Remedy: Large  suppliers  will certainly  purchase  unique dies for punching  openings, but for  brand-new  pals who  have actually  simply  bought wood pellet  manufacturing, die  obstructing is a  migraine. read 

3. During the  manufacturing process,  as a result of power failure or  various other reasons, the mold is blocked,  particularly the small-diameter  mold and mildew is difficult to  tidy. Drilling the material with a power drill is  extra common in wood pellet  manufacturing equipment, but this is time consuming  as well as tends to damage the  level of smoothness of the die  openings.  Additionally, after the die is punched, it  requires to be re-ground  prior to it can be used normally, which affects the work  effectiveness.

 Option: A  much more  reliable  method is to use oil to  steam the ring die,  to ensure that the plug hole is completely immersed in the oil  and afterwards heat  all-time low of the oil  frying pan until the material in the plug hole makes a popping  noise, i.e.  get rid of the plugging die, re-install the machine after cooling,  Readjust the gap of the die rolls, according to the  procedure  demands of the wood pellet mills, the  product in the  obstructed die can be  rapidly cleaned by re-driving.


For details please contact: Richi Machinery 
WhatsApp:86 138 3838 9622
Email:enquiry@pellet-richi.com
Pellet Richi
Written by

Pellet Richi

Pellet machine manufacturer

Post a comment